Bölüm "Fakülteler, Mühendislik ve Doğa Bilimleri Fakültesi, Makine Mühendisliği Bölümü" için listeleme
Toplam kayıt 61, listelenen: 1-20
-
Analysis of Tribo-corrosion Properties of MAO/DLC Coatings Using a Duplex Process on Ti6Al4V Alloys
(Springer International Publishing, 2015)In recent years, various technologies have been increasingly investigated for the surface modification of Ti and Ti alloys. Microarc oxidation (MAO) is one of the effective techniques to improve surface properties. However, ... -
Angular Momentum Control for Preventing Rollover of a Heavy Vehicle
(Society of Automotive Engineers Turkey, 2022)In this article, gyroscopes and flywheels are used to prevent the rollover of a vehicle due to external forces. The rollover preventing performance of the flywheels for a heavy trailer (an inverted pendulum problem) is ... -
Atık NdFeB Mıknatıs Katkılı Silikon Esaslı Kompozit Üretilmesi ve Mekanik Özelliklerinin Deneysel olarak İncelenmesi
(1st International Eurasian Conference on Science, Engineering and Technology (EurasianSciEnTech 2018), Ankara, 2018)Atık NdFeB katkılı silikon esaslı manyetik polimer kompozitler çift katkı maddeli karışımın %70-%30 oranında karıştırılması neticesinde elde edilmektedir. NdFeB manyetik partikülün partikül boyutları (0–45, 45–63, 63–125, ... -
Comparison of Mechanical Properties Obtained for Armor Steels: Conventional Methods vs. Nanoindentation
(ASTM International, 2023)The mechanical properties of three armor steels, namely Ramor 500, Ramor 550, and Armox Advance, were acquired by nanoindentation and conventional methods, and then the results were compared. To this goal, samples were ... -
ÇATI ARALARINDA MEYDANA GELEN DOĞAL TAŞINIMLA ISI TRANSFERİNİN ÇATI KATINDAKİ ISIL KONFORA ETKİSİNİN SAYISAL ANALİZİ
(IV. EGE ENERJİ SEMPOZYUMU, 2008-05-21)İki boyutlu, çatı ile bütünleşik kapalı ortamlarda yaz ve kış sınır şartları için çatı aralarında meydana gelen doğal taşınımla ısı transferinin çatı katındaki ısıl konfora etkisi sayısal olarak incelenmiştir. Kış sınır ... -
Damage assessment of Siverek Castle during the Kahramanmaraş Earthquakes (Mw 7.7 and Mw 7.6) on 06 February 2023: Remediation and strengthening proposals
(Elsevier B.V., May 2024)On February 6, 2023, two significant earthquakes with magnitudes (Mw) of 7.7 and 7.6 struck Turkey, occurring nine hours apart. In addition to the tragic loss of over 50,000 lives in the earthquakes centered in Kahramanmaraş, ... -
Dietil eter-motorin karışımlarının motor performansına etkilerinin deneysel incelenmesi
(Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 2012)Bu çalışmada, dietil eter (DEE)-motorin karışımlarının motor performansına etkileri deneysel olarak incelenmiştir. Yakıt karışımları motorin içerisine hacimsel olarak %2,5, %5, %7,5 ve %10 oranlarında dietil eter karıştırılarak ... -
DUBLEKS EV BENZERİ KAPALI ORTAMLARDA DOĞAL TAŞINIMLA ISI TRANSFERİNİN SAYISAL İNCELENMESİ
(ULIBTK’07, 2007-05-30)Dubleks ev benzeri kısmi olarak bölünmüş kapalı ortamlardaki doğal taşınımla ısı transferi sayısal olarak incelendi. Yaz ve kış sınır şartları altındaki doğal taşınım problemi iç bölmenin iki farklı konumu ve iç bölme ... -
DUBLEKS EV GEOMETRİSİNE SAHİP KAPALI ORTAMLARDA FARKLI ISITMA YÖNTEMLERİNİN DOĞAL TAŞINIMLA ISI TRANSFERİ ÜZERİNE ETKİLERİNİN SAYISAL ANALİZİ
(VIII. Ulusal Tesisat Mühendisliği Kongresi TESKON, 2007)Dubleks ev benzeri kısmi olarak bölünmüş kapalı ortamlardaki doğal taşınımla ısı transferi sayısal olarak incelendi. Kış sınır şartları altındaki doğal taşınım problemi, alttan ısıtma ve yan yüzeyden kısmi olarak ısıtma ... -
Economic analysis and sustainability of Turkish marine hatcheries
(2010)Çalışmada, Türkiye deniz balıkları yavru üretiminin %61,5’ini karşılayan 7 lider kuluçkahane için ekonomik analiz gerçekleştirilmiş ve sürdürülebilirlikleri değerlendirilmiştir. Bunun için, yatırım masraflarını içeren sabit ... -
The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy
(Springer Nature, 2024)In this study, the microstructure, hardness, tensile strength, and dry wear properties of the cast AlSi10Mg alloy as well as the effects of processing parameters on the oxidation behavior of this alloy were investigated. ... -
Effect of Isothermal Treatment on Mechanical and Tribological Properties of Alloy Zn – 40% Al – 2% Cu – 2% Si
(Springer, 2023)The effect of isothermal exposure at temperatures from 100°C to 250°C for 8 hours on the structure, mechanical and tribological properties of the Zn – 40% Al – 2% Cu – 2% Si alloy produced by chill casting is studied. The ... -
Effect of Plastic Deformation on the Mechanical Properties of Dual-Phase Steels Using Nanoindentation
(Springer, 2023)The mechanical properties of two advanced high-strength steels (AHSS), DP 1000 and DP 1200 dual-phase (DP) grades, under deformed and undeformed conditions, were investigated using nanoindentation, and the results were ... -
The Effect of Surface Roughness on Fatigue Life in AZ31 Magnesium Alloy
(Springer, 2023)Magnesium alloys have excellent properties such as high specific strength, rigidity, good damping, electromagnetic shielding, castability, and machinability. However, corrosion, creep, and fatigue resistance are generally ... -
Effect of thickness and melting temperature of phase change material integrated into exterior wall on building energy performance and CO2 emission reduction
(Gazi Universitesi, 2024)In the study, the effect of phase change materials integrated into the building's external wall has been investigated in terms of material type, thickness, and melting temperature of phase change material on the building ... -
Effect of Working Conditions on the Lubricated Wear Behavior of Zn-40Al-2Cu-2Si Alloy in the As- Cast and T6 Heat-Treated States
(American Society of Mechanical Engineers (ASME), 2022)In order to determine the effect of working conditions on the lubricated wear behavior of Zn-40Al-2Cu-2Si alloy in the as-cast and T6 heat-treated states, its tribological properties were studied at different oil flowrates, ... -
Effect of Working Conditions on the Lubricated Wear Behavior of Zn-40Al-2Cu-2Si Alloy in the As-Cast and T6 Heat-Treated States
(ASME, 2022)In order to determine the effect of working conditions on the lubricated wear behavior of Zn-40Al-2Cu-2Si alloy in the as-cast and T6 heat-treated states, its tribological properties were studied at different oil flowrates, ... -
Effects of Methanol Addition to Gasoline on the Performance and Fuel Cost of a Spark Ignition Engine
(Energy & Fuels (ACS Publishers), 2008)This study is concerned with investigating experimentally the effects of methanol blending to base gasoline on the performance and fuel cost of a spark ignition (SI) engine. The fuel blends were prepared by blending 5, 10, ... -
Effects of Methyl tert-Butyl Ether Addition to Base Gasoline on the Performance and CO Emissions of a SI Engine
(Energy & Fuels (ACS Publications), 2008)This study aims at investigating experimentally the effects of methyl tert-butyl ether (MTBE)-gasoline blends on the performance and CO emissions of a spark ignition engine. The blends are prepared by blending 5, 10, 15, ... -
Effects of the Stroke Bore Ratio on the Performance Parameters of a Dual-Spark-Ignition (DSI) Engine
(Energy & Fuels (ACS Publishers), 2009)In this study, the effects of the stroke/bore (S/B) ratio on the performance parameters of an engine having dual-spark ignition (DSI) were investigated theoretically by using a quasi-dimensional thermodynamic cycle model. ...