Bölüm "Fakülteler, Mühendislik ve Doğa Bilimleri Fakültesi, Makine Mühendisliği Bölümü" Scopus İndeksli Yayınlar Koleksiyonu için listeleme
Toplam kayıt 24, listelenen: 1-20
-
Analysis of Tribo-corrosion Properties of MAO/DLC Coatings Using a Duplex Process on Ti6Al4V Alloys
(Springer International Publishing, 2015)In recent years, various technologies have been increasingly investigated for the surface modification of Ti and Ti alloys. Microarc oxidation (MAO) is one of the effective techniques to improve surface properties. However, ... -
Angular Momentum Control for Preventing Rollover of a Heavy Vehicle
(Society of Automotive Engineers Turkey, 2022)In this article, gyroscopes and flywheels are used to prevent the rollover of a vehicle due to external forces. The rollover preventing performance of the flywheels for a heavy trailer (an inverted pendulum problem) is ... -
Comparison of Mechanical Properties Obtained for Armor Steels: Conventional Methods vs. Nanoindentation
(ASTM International, 2023)The mechanical properties of three armor steels, namely Ramor 500, Ramor 550, and Armox Advance, were acquired by nanoindentation and conventional methods, and then the results were compared. To this goal, samples were ... -
Damage assessment of Siverek Castle during the Kahramanmaraş Earthquakes (Mw 7.7 and Mw 7.6) on 06 February 2023: Remediation and strengthening proposals
(Elsevier B.V., May 2024)On February 6, 2023, two significant earthquakes with magnitudes (Mw) of 7.7 and 7.6 struck Turkey, occurring nine hours apart. In addition to the tragic loss of over 50,000 lives in the earthquakes centered in Kahramanmaraş, ... -
Economic analysis and sustainability of Turkish marine hatcheries
(2010)Çalışmada, Türkiye deniz balıkları yavru üretiminin %61,5’ini karşılayan 7 lider kuluçkahane için ekonomik analiz gerçekleştirilmiş ve sürdürülebilirlikleri değerlendirilmiştir. Bunun için, yatırım masraflarını içeren sabit ... -
The Effect of Heat Treatment on the Mechanical Properties and Oxidation Resistance of AlSi10Mg Alloy
(Springer Nature, 2024)In this study, the microstructure, hardness, tensile strength, and dry wear properties of the cast AlSi10Mg alloy as well as the effects of processing parameters on the oxidation behavior of this alloy were investigated. ... -
Effect of Isothermal Treatment on Mechanical and Tribological Properties of Alloy Zn – 40% Al – 2% Cu – 2% Si
(Springer, 2023)The effect of isothermal exposure at temperatures from 100°C to 250°C for 8 hours on the structure, mechanical and tribological properties of the Zn – 40% Al – 2% Cu – 2% Si alloy produced by chill casting is studied. The ... -
Effect of Plastic Deformation on the Mechanical Properties of Dual-Phase Steels Using Nanoindentation
(Springer, 2023)The mechanical properties of two advanced high-strength steels (AHSS), DP 1000 and DP 1200 dual-phase (DP) grades, under deformed and undeformed conditions, were investigated using nanoindentation, and the results were ... -
The Effect of Surface Roughness on Fatigue Life in AZ31 Magnesium Alloy
(Springer, 2023)Magnesium alloys have excellent properties such as high specific strength, rigidity, good damping, electromagnetic shielding, castability, and machinability. However, corrosion, creep, and fatigue resistance are generally ... -
Effect of thickness and melting temperature of phase change material integrated into exterior wall on building energy performance and CO2 emission reduction
(Gazi Universitesi, 2024)In the study, the effect of phase change materials integrated into the building's external wall has been investigated in terms of material type, thickness, and melting temperature of phase change material on the building ... -
Energy and economic assessments of waste heat recovery by designs of economizer, condensing economizer and air preheater
(Gazi Universitesi, 2023)In this study, the waste heat loss of flue gases from the boilers of Kafkas University district heating system has been calculated between 6-8% according to the combustion analysis and the annual cost of this heat loss has ... -
Enhanced wear resistance and surface properties of oxide film coating on biocompatible Ti45Nb alloy by anodization method
(Elsevier B.V., 2023)β-Titanium alloys have become increasingly popular as biomaterials because of their low modulus of elasticity and superior corrosion properties in recent years. β-titanium alloy containing niobium is also a biocompatible ... -
Gyroscopic suspension for a heavy vehicle
(Inderscience Publishers, 2023)In this study, an angular momentum generated by a flywheel gyroscope is performed as a suspension to prevent vehicle vibration. The frequency equations are derived and the optimal flywheel speed is obtained for vibration ... -
High-cycle fatigue and tensile strength of AZ91 Mg alloy with MAO-epoxy duplex coating
(Institute of Materials and Machine Mechanics, 2023)In this study, an epoxy layer was formed by the immersion process, on the oxide layer grown by the micro-arc oxidation (MAO) treatment of the AZ91 magnesium alloy, using the thin film sealing technology, and its effect on ... -
Influence of nickel addition on the microstructure, mechanical, and wear properties of Zn-40Al-2Cu alloy
(John Wiley and Sons Inc, March 2024)To study the influence of nickel addition on the microstructure, mechanical and lubricated wear properties of Zn-40Al-2Cu alloy, one ternary and five quaternary Zn-40Al-2Cu-(0.5-2.5)Ni alloys were made by permanent mold ... -
Influence of post processing on the mechanical properties and wear behavior of selective laser melted Co-Cr-Mo-W alloys
(Elsevier Ltd, 2024)In the study, the effect of laser energy density and post-processes (sintering, cold rolling, and hot rolling) on the properties of Co-Cr-Mo-W alloys fabricated by selective laser melting (SLM) are investigated. The samples ... -
Investigation of friction behavior of TiO2: Al2O3 composite coating formed on AA2024 alloy by micro-arc oxidation
(Yildiz Technical University, February 2)In this study, an alumina (Al2O3) ceramic coating and a composite coating containing titanium dioxide (TiO2) particles were prepared on surfaces of AA2024 substrates by micro-arc oxidation (MAO) treatment. The effects of ... -
Investigation of the Effects of Filling Speed, Casting Temperature and Metallurgical Quality on Fluidity of Lamellar Graphite Cast Iron at Different Section Thicknesses
(Springer Science and Business Media Deutschland GmbH, 2024)In this study, the fluidity properties of the alloy were investigated at different casting temperatures, different section thicknesses, and varying casting parameters of lamellar graphite cast iron materials. To achieve ... -
Investigation of used PCM-integrated into building exterior walls for energy savings and optimization of PCM melting temperatures
(Elsevier Ltd, 2023)In the study, the effects on the building's thermal energy performance of using two different phase change materials (PCMs) integrated into the exterior walls at various thicknesses and melting temperatures have been ... -
Nano materyal içerikli katkıların yakıt özelliklerine ve yanma karakteristiklerine etkileri
(2019)Bu çalışma; dizel, biyodizel, su içeren emülsiyon yakıtları ve çeşitli yakıt karışımları gibi dizel motor yakıtlarında nano materyal içerikli katkıların kullanımı üzerine yapılmış çeşitli çalışmaların sonuçlarından ...